$ € £ Cart: 0 products (empty) Log in Home Contact How Coupons Sitemap
A clean desk surface with a technical document binder and a tablet displaying a standards cover page, warm beige and charcoal tones, professional atmosphere

SAE J1939-13 connector pin and PGN guide

SAE J1939-13 specifies the off-board diagnostic connector used to access the controller area network on many heavy vehicles and mobile machines. It is common on Australian trucks, buses, prime movers, construction equipment and mining fleets, where a workshop scanner must interrogate engine, transmission, brake and body electronic control units without dismantling the vehicle.

The connector is the physical gateway; the Parameter Group Number, or PGN, identifies the message carried across the network. A cable may look capable of carrying every message, but the attached tool, ECU software and vehicle configuration determine which PGNs can actually be requested and decoded. Connector compliance alone does not guarantee diagnostic coverage.

Pin assignment errors produce misleading symptoms: a scan tool may stay silent, report intermittent power faults or fail to wake sleeping modules. Good practice is to treat the connector wiring, vehicle supply, ground paths and termination as one system, then verify every measurement against the applicable edition of the standard.

For Australian users, the distinction matters in Sydney and Melbourne interstate fleets, Brisbane urban buses, and remote operations in the Pilbara, Hunter Valley and Bowen Basin. J1939 diagnostics support maintenance, but they do not replace Australian Design Rules, ADR heavy-vehicle emissions requirements, state roadworthiness checks or the National Heavy Vehicle Vehicle Code.

Connector purpose and physical interface

J1939-13 defines a keyed, locking 16-way diagnostic interface for the vehicle side of the connection. A matching cable or vehicle-specific adapter brings the diagnostic tool to the socket, while the connector provides signal and power contacts under the environmental and mechanical conditions expected on road and off-road equipment. Before purchasing a copy, readers can follow the code access guide to see how downloadable standards are organised and delivered.

This interface is not interchangeable with the 16-pin OBD socket used for many light vehicles. J1939-13 supports the 250 kbit/s network defined by J1939-11 and carries diagnostic traffic alongside operational messages. The tool must present any required bus termination, supply the expected power and wake connections, and use a harness compatible with the vehicle’s connector and grounding arrangement.

Pin assignment at a glance

In the J1939-13 pin assignment, pins 6 and 7 carry Data+ and Data−, the two conductors of the differential network. Pin 11 provides the battery-positive supply, pin 14 is the wake-up connection, and the remaining listed contacts—including pins 1–5, 8–10, 12–13 and 15–16—provide ground paths. The repeated ground arrangement supports dependable reference and return connections.

A diagnostic lead should mate without forcing, latch positively and use the correct pin geometry. Inspect for bent contacts, moisture, corrosion and damaged seals, then check supply voltage and continuity before blaming an ECU. Because pin numbering is easy to misread on a workshop diagram, confirm the connector marking and standard revision rather than relying on an unlabelled photograph.

Reading identifiers and PGN structure

A PGN is extracted from the 29-bit CAN identifier, not from the connector pins. The identifier carries priority, PGN, source-address and destination information according to the PDU format. A global destination is address 255, allowing a tool to request the same data from every responding module without first identifying each controller.

Request PGN 59904 asks an ECU or global address to send data. A directed request identifies one module, while a global request uses destination 255. Multi-frame diagnostics use transport protocols such as BAM at PGN 60160 or the RTS/CTS exchange at PGN 60416, allowing a gateway to combine several frames into one larger message.

PGN numbers describe a message group, while Suspect Parameter Numbers, or SPNs, identify individual data items within it. OEM proprietary ranges may also carry useful fault information, but their meaning depends on manufacturer documentation. A correct connector and a recognised PGN still do not guarantee that a generic scanner displays a parameter.

Mapping common PGNs to workshop data

A workshop map should connect each PGN to its SPN definitions, byte order, scaling and valid ranges. Common examples include PGN 60928 for engine speed using SPN 190, PGN 65262 for engine coolant temperature using SPN 110, PGN 65268 for vehicle speed using SPN 84, PGN 65269 for accelerator pedal position 1 using SPN 512, and PGN 65279 for engine hours and revolutions.

Decoding then applies the published conversion rather than treating raw bytes as direct readings. Engine speed is commonly scaled at 0.125 rpm per bit, while coolant temperature uses a 1 °C-per-bit resolution with a −40 °C offset. A displayed value should be traced through the PGN, SPN and byte definition before a sensor is condemned.

Diagnostic and proprietary PGNs may expose active faults, freeze-frame data or component status, but support varies by ECU and model year. Keep the correct J1939-family application data with the connector standard, and use manufacturer service information for Australian vehicles whose dashboards, emissions systems or body controls have been retrofitted or modified.

Australian workshop and procurement use

In Australia, the standard is especially relevant to fleets servicing articulated trucks in Melbourne, interstate buses leaving Sydney, construction plant around Brisbane and autonomous mining trucks in Western Australia. Technicians use J1939 to read live engine and transmission data, examine fault codes and test modules after wiring or sensor work.

Those results support maintenance decisions, but they do not certify compliance. An exhaust or driveline modification can interact with ADR requirements, National Heavy Vehicle Vehicle Code provisions and state or territory roadworthiness inspections. Diagnostic records should identify the vehicle, ECU software context and any aftermarket changes.

Document Bays supplies downloadable PDFs, so Australian buyers normally avoid a physical parcel, freight consignment and customs-broker process. They should still confirm whether AUD and GST appear on the invoice, retain the receipt for tax records and check the treatment of digitally supplied imported services. The store provides secure payment options, with multiple currencies and major payment methods available for the transaction.

Download the applicable SAE J1939-13 document from Document Bays, verify its revision against the equipment service information, and keep it beside the related J1939-21 application-layer information. That combination gives Australian technicians a dependable basis for wiring verification, targeted PGN requests and defensible fault diagnosis across road and off-road fleets.

Quick Inquiry

Questions about an order or a specific standard? Use our contact form.

Contact Us

Secure payment with SSL

Featured Products

ANSI/ASHRAE

ANSI/ASHRAE 149-2013

$17.63 Add to Cart
ANSI/HI

ANSI/HI 11.6-2012

$40.85 Add to Cart
ANSI/ASSE

ANSI/ASSE Z690 Package

$60.20 Add to Cart
ANSI/ASHRAE

ANSI/ASHRAE 113-2013

$17.63 Add to Cart
ANSI/HI

ANSI/HI 14.6-2011

$83.85 Add to Cart
ANSI/ALI

ANSI/ALI A14 Standards Set

$645.00 Add to Cart

About Standards Store

We provide industry standards and codes in PDF format for immediate download. Our catalog spans engineering, manufacturing, construction, and quality management — with documents from over 50 issuing bodies worldwide.

Learn More

Latest Additions

Recently added standards include AWS D14.4/D14.4M-2019, API RP 581-2019, ISO/IEC 17025:2017, RTCA DO-363, and IPC/ECA J-STD-002E. Visit the New Standards section for the complete list.

New Standards

Secure Payment

All transactions are protected with SSL encryption. We accept Visa, Mastercard, and PayPal. Use coupon codes at checkout for additional discounts on eligible items.

Payment Info

Standards Store is dedicated to making technical standards and codes accessible to professionals worldwide. Every document in our catalog is delivered as a PDF for immediate download — no shipping, no waiting. We serve engineers, quality assurance specialists, manufacturers, and contractors who rely on accurate, up-to-date standards for their work.

Browse by issuing organization, explore new additions, or check our specials for discounted titles.

For questions about an order or for information about our products, please use the contact form below. Select the appropriate subject — Customer Service for order inquiries or Webmaster for technical issues with the website.

We aim to respond promptly to all inquiries.

Send a Message