$ € £ Cart: 0 products (empty) Log in Home Contact How Coupons Sitemap
A clean desk surface with a technical document binder and a tablet displaying a standards cover page, warm beige and charcoal tones, professional atmosphere

JIS G 4304 mechanical property test sampling locations

The sampling locations specified in JIS G 4304 determine how a mill converts a heat of hot-rolled stainless steel plate, sheet or strip into traceable mechanical-property evidence. Coupon position, rolling direction and thickness affect whether a result represents the centre, edge and through-thickness condition of the delivered product. That distinction matters when plate becomes pressure equipment, process tanks, wear liners or structural components.

Japanese material specifications frequently reach Australian workshops through replacement stock for imported plant. Engineers must therefore connect the standard’s sampling rule to the ordered grade, product form, thickness and mill certificate; a tensile result taken from an unidentified offcut is not equivalent to a controlled standard sample.

Scope and purpose of the sampling requirements

JIS G 4304 covers hot-rolled stainless steel plate, sheet and strip across austenitic, ferritic, martensitic and duplex grades, including SUS304, SUS316 and related variants. Its mechanical requirements address tensile strength, proof stress or yield strength, elongation and, where specified, hardness. Limits vary by grade and thickness, so an acceptable result cannot be selected without the correct product classification.

The standard uses tensile and hardness test methods to verify those requirements, commonly aligned with JIS Z 2241 and JIS Z 2251. Sampling is not simply taking a piece from the sheet: the material must represent the specified heat or lot and rolling condition. For teams building a controlled specification, Document Bays’ using technical codes guidance helps identify the relevant clause, amendment status and supporting definitions.

Specimen positions for plate, sheet and strip

Product category Tensile specimen orientation Sampling location Engineering significance
Hot-rolled plate or sheet, 8 mm and over Transverse to the rolling direction Centre-width position shown in the applicable sampling diagram Exposes cross-direction and through-thickness influences
Hot-rolled sheet below 8 mm Longitudinal, parallel to the rolling direction Defined longitudinal position within the sheet width Retains sufficient material for a valid specimen
Hot-rolled strip Longitudinal Designated position across the usable strip width Reflects narrow, continuously rolled material geometry

The usual orientation pattern is transverse for plate and sheet at or above 8 mm and longitudinal below that thickness; strip is normally sampled longitudinally. These orientations expose different mechanical responses, particularly the cross-direction effects that can influence formed or welded components. The marked width position and any stated edge distance in the current sampling diagram remain part of the requirement.

Every coupon must come from sound material, with the sheared edge, visible scale, grinding damage, repair weld and other surface discontinuities excluded unless their condition is being assessed. If a purchase specification calls for supplementary centre, edge, longitudinal or transverse coupons, each must be identified separately. Such an agreement must be documented before testing rather than added after the results are known.

Building a representative mechanical test plan

A defensible plan identifies the grade, standard edition, product form, nominal thickness, width, heat or cast number, rolling condition and required tests. It then maps each specimen to a drawing showing its orientation and position within the product. This matters when an Australian fabrication order combines material from several heats or mills: a certificate covering one heat cannot stand in for another.

Coupon preparation can also affect the result. Sawing, milling, grinding and polishing must follow the applicable test method and surface condition. Hardness readings may be influenced by rolled scale, decarburisation or a work-hardened layer, so a hardness position should not automatically be assumed to match the tensile-coupon position.

Australian drawings normally use millimetres and express strength in MPa or N/mm², allowing metric test reports to be incorporated without conversion. Melbourne and Sydney workshops often maintain Japanese-specified replacement plate for imported food and pharmaceutical equipment. Perth mining and water-service projects use corrosion-resistant grades, while salt-exposed Brisbane infrastructure makes corrosion suitability a separate consideration from mechanical conformity. State and territory work health and safety laws based on the Safe Work Australia model also govern sharp edges, noise and hot-work during plate preparation.

Audit-ready sampling and certification records

An auditable file should show where each specimen came from, not merely the final numerical values.

Location and specimen checks

  • Grade, standard edition, heat or cast number, product form and rolling condition
  • Plate thickness and width, coupon orientation, sampling zone and edge distance
  • Specimen dimensions, gauge length, surface preparation and any departure from the standard

Certificate and traceability checks

  • Test method, laboratory, specimen identification and report date
  • Mechanical-property values compared with the grade and thickness-specific limits
  • Purchase-order deviations, supplementary tests and linkage to the shipped heat

These checks close the gap between a reported result and usable engineering evidence. A certificate that lists tensile values but cannot identify the heat, orientation or test method offers limited assurance during procurement or fabrication.

Training rooms can make the sampling logic easier to understand through enlarged diagrams and colour-coded coupon maps. Tasteful decorative wall art can complement that visual environment, while controlled PDF copies remain the source of technical requirements.

Prepare a controlled test package

Before requesting the document, identify the grade, product category, thickness range and whether the material is plate, sheet or strip. Establish whether ordinary JIS G 4304 requirements or supplementary tensile, corrosion, ultrasonic or surface tests are required by the contract.

The purchase specification should name the standard and edition, approved supplier, mill-certificate format, retained samples, testing laboratory, report language, result units and any supplementary sampling position. Project documentation should reconcile the Japanese requirement with the drawing, applicable AS/NZS standards and Australian workplace controls.

Choose the current JIS G 4304 PDF from Document Bays, pay in AUD or another supported currency using a major payment method, and use the immediate download for controlled project use. Record the document revision, issue the sampling plan with the order, and require the returned report to match the same heat, thickness class and coupon location.

Quick Inquiry

Questions about an order or a specific standard? Use our contact form.

Contact Us

Secure payment with SSL

Featured Products

ANSI/ASHRAE

ANSI/ASHRAE 149-2013

$17.63 Add to Cart
ANSI/HI

ANSI/HI 11.6-2012

$40.85 Add to Cart
ANSI/ASSE

ANSI/ASSE Z690 Package

$60.20 Add to Cart
ANSI/ASHRAE

ANSI/ASHRAE 113-2013

$17.63 Add to Cart
ANSI/HI

ANSI/HI 14.6-2011

$83.85 Add to Cart
ANSI/ALI

ANSI/ALI A14 Standards Set

$645.00 Add to Cart

About Standards Store

We provide industry standards and codes in PDF format for immediate download. Our catalog spans engineering, manufacturing, construction, and quality management — with documents from over 50 issuing bodies worldwide.

Learn More

Latest Additions

Recently added standards include AWS D14.4/D14.4M-2019, API RP 581-2019, ISO/IEC 17025:2017, RTCA DO-363, and IPC/ECA J-STD-002E. Visit the New Standards section for the complete list.

New Standards

Secure Payment

All transactions are protected with SSL encryption. We accept Visa, Mastercard, and PayPal. Use coupon codes at checkout for additional discounts on eligible items.

Payment Info

Standards Store is dedicated to making technical standards and codes accessible to professionals worldwide. Every document in our catalog is delivered as a PDF for immediate download — no shipping, no waiting. We serve engineers, quality assurance specialists, manufacturers, and contractors who rely on accurate, up-to-date standards for their work.

Browse by issuing organization, explore new additions, or check our specials for discounted titles.

For questions about an order or for information about our products, please use the contact form below. Select the appropriate subject — Customer Service for order inquiries or Webmaster for technical issues with the website.

We aim to respond promptly to all inquiries.

Send a Message